99 Results Found
This short example illustrates basic VLAN operation. Examining VLANs in a large-scale installation can show the full benefits of VLANs. Consider that this is a small portion of a large corporate headquarters with 5,000 devices connected in a 20 building campus.
In 1998, the Internet Engineering Task Force (IETF) released RFC 2460, outlining the technical specifications of IPv6, which addressed the shortcomings of the aging IPv4 protocol. As with any evolution of technology, new elements exist in the protocol that may seem strange and unfamiliar. This certainly includes address representation, space, and so forth, but also includes a number of different types of addresses as well. A subset of these new addressing types has corresponding types in IPv4, but many will seem significantly different. The purpose of this white paper is to examine addressing classifications in detail and outline their functions within the context of the protocol.
Depending on the switch vendor, the exact steps will vary on how to set up and configure VLANs on a switch. For the network design shown, the general process for setting up VLANs on the switch is:
Now that the network is installed, each switch has a bridge ID number, and the root switch has been elected, the next step is for each switch to perform a calculation to determine the best link to the root switch. Each switch will do this by comparing the path cost for each link based on the speed. For paths that go through one or more other switches, the link costs are added. The switch compares this aggregate value to the other link costs to determine the best path to the root switch.
That depends on their configurations. For example: While it makes very good sense to include redundant physical links in a network, connecting switches in loops, without taking the appropriate measures, will cause havoc on a network. Without the correct measures, a switch floods broadcast frames out all of its ports, causing serious problems for the network devices. The main problem is a broadcast storm where broadcast frames are flooded through every switch until all available bandwidth is used and all network devices have more inbound frames than they can process.
I recently responded to a message on LinkedIn from a regular reader of this blog. He asked several questions which I will answer over the course of several posts. As part of his first question, he described a strategy report that his group is producing. The audience for this strategy report considers ITIL important to the future of their business, and so he must describe which ITIL processes his data center operations group works most closely with.
The most obvious difference is that hubs operate at Layer 1 of the OSI model while bridges and switches work with MAC addresses at Layer 2 of the OSI model. Hubs are really just multi-port repeaters. They ignore the content of an Ethernet frame and simply resend every frame they receive out every interface on the hub. The challenge is that the Ethernet frames will show up at every device attached to a hub instead of just the intended destination (a security gap), and inbound frames often collide with outbound frames (a performance issue).
“Twisted Pair” is another way to identify a network cabling solution that’s also called Unshielded Twisted Pair (UTP) and was invented by Alexander Graham Bell in 1881. Indoor business telephone applications use them in 25-pair bundles. In homes, they were down to four wires, but in networking we use them in 8-wire cables. By twisting the pairs at different rates (twists per foot), cable manufacturers can reduce the electromagnetic pulses coming from the cable while improving the cable’s ability to reject common electronic noise from the environment.
Good question! There are lots of networks, so I’m sorry to say that it depends. Let me explain. The smallest computer-based networks are usually PANs or Personal Area Networks. They can connect a wireless keyboard, mouse, or other devices to a computer. You may find them wirelessly linking a printer to your computer. You may have noticed these all include wireless connections. A PAN most often uses wireless technologies like infrared and Bluetooth, so it is really a WPAN (Wireless Personal Area Network).
For us wireless folks that aren’t stellar routing and switching guys, one of the most daunting network tasks is integrating our WLAN infrastructure with the existing wired infrastructure and its services. Understanding wired design topics is pretty fundamental to installing or managing any network, so it really should be on our priority list to spruce up those skills. To give you a nudge on your journey, let’s talk about DHCP for wireless clients.