Is your salary on par with others in your field? Learn more in Skillsoft's 2024 IT Skills and Salary Report. Click Here.

Checkout

Cart () Loading...

    • Quantity:
    • Delivery:
    • Dates:
    • Location:

    $

Contact Sales

Static Routing

Date:
July 14, 2009
Author:
Guest Authors

You may have noticed that it’s the dynamic routing protocols that get all the glory. Since I like rooting (routing?) for the underdog, let’s talk about static routes!

As you may recall, a router has three methods for learning a route. A route can appear in the routing table if it is:


  • Connected – directly attached

  • Dynamic - learned via a routing protocol

  • Static – configured by a person


A static route is a route that manually inserted into the routing table. Static routes appear in the routing table as “S” routes, and are often used:

  • When there is only one path to reach a destination

  • As a backup route to a destination


Static routes are created in global config mode, and require a destination prefix and a way to get there. For example, let’s say that our router’s Serial 1/1 interface, with an IP address of 192.168.1.5/30, has a point-to-point link to another router’s Serial 2/2, with IP address 192.168.1.6/30. We’ve been told that we can reach the 10.2.3.0/24 subnet via the neighbor router. To configure a static route, the command could be:

  • Router(config)#ip route 10.2.3.0 255.255.255.0 192.168.1.6


Note that the next hop address is our neighbor’s address (not ours). In the case of a point-to-point serial link, you also have the option of using the outbound interface, like this:

  • Router(config)#ip route 10.2.3.0 255.255.255.0 serial 1/1


Note that when the interface option is specified, it’s our interface (not the neighbor’s). The interface option only works with point-to-point links, such as serial links running HDLC or PPP. The interface option will not work with multi-point interfaces, such as LANs, Frame Relay, or ATM. This is because the multi-point topologies require a Layer 2 address (MAC, DLCI, or VPI/VCI, for example), and it’s necessary to have the next-hop’s IP address to resolve this.

If you configure a static route using the outbound interface on a multi-access link (such as Ethernet or Frame Relay), you won’t get a syntax error, but routing will fail. In fact, “debug ip packet” will reveal “encapsulation failed” for packets following that route, indicating that the router was unable to build the frame header due to lack of a Layer-2 destination address. You must use the “next-hop” option when configuring a static route on a multi-access media.

Note that although they appear in the running config as soon as they are created, by default a static route will only be inserted into the routing table if the router believes that the next hop is actually reachable. In other words, for the static route to appear in the routing table, the interface used to reach the next hop must be “up/up”.

Contrary to what you might read (including in some Cisco documentation), the default administrative distance (AD) for a static route is one, regardless of whether the next hop or outbound interface is used. By default, the only thing that beats a static route is a connected route, with an AD of zero.

You can however, change the AD of a static route. Let’s say that your router is learning the route to 10.2.3.0/24 via OSPF, which has a default AD of 110. Now suppose that you configure a static route to 10.2.3.0/24 with an AD of 250, like this:


  • Router(config)#ip route 10.2.3.0 255.255.255.0 192.168.1.6 250


If the link is point-to-point, you could also do it like this:

  • Router(config)#ip route 10.2.3.0 255.255.255.0 serial 1/1 250


Note that the value following the next hop, or outbound interface, is the AD for the static route. Since when choosing a route it’s the low AD that wins, as long as the route is being learned by OSPF, it’s the OSPF route that will appear in the routing table (110 beats 250). If the OSPF route is no longer available, then the static route will appear in the routing table. This type of static route is referred to as a “floating” static route, and it is sometimes used for backup links.

You can also specify a “tag” when configuring a static route. This is done by using the keyword “tag”, like this:


  • Router(config)#ip route 10.2.3.0 255.255.255.0 192.168.1.6 tag 1000


The tag can then be matched with a route map (a glorified access list that allows you to permit, deny, and change parameters of routing advertisements). And, of course, you can also specify a tag along with an admin distance:

  • Router(config)#ip route 10.2.3.0 255.255.255.0 serial 1/1 250 tag 1000


Static routes have other options as well. No sense letting the dynamic protocols have all the fun!

Author: Al Friebe